Tartan Buffalo Plaid Pattern Vinyl Siser HTV & Adhesive Craft Vinyl Oracal

Available in heat transfer vinyl HTV, permanent adhesive (sign) craft vinyl & reusable, no residue, removable adhesive vinyl & decal Tons of patterns & options! Contact us if you'd like to make a special request or custom pattern! Professionally Printed Pattern Vinyl for HTV - Craft Vinyl - Decal High-quality pattern vinyl3 Options to choose from: Siser Colorprint Easy Iron On Heat Transfer Vinyl Patterned Oracal 651 Glossy Permanent Adhesive Craft Vinyl Reusable No Residue Removable Adhesive VinylBundle discounts available!Cut out any shape or design & apply!Take advantage of our huge selection of patterns & colors!Please be sure to check out the easy application instructions below!All you need is a plotter or cutter! Iron for HTV All Patterns are printed with a large format Roland printer that uses Eco-solvent genuine inks.Permanent Adhesive Craft Vinyl (Outdoor/Indoor Vinyl) Printable Oracal 651 - No Transfer Tape ProvidedGreat to use on glass, metal, plastic, and much more! Please clean surface before use!Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply a transfer tape to transfer design off of the backing and place on your smooth & clean surfaceWeatherproof / 4+ years durabilityReusable No Residue Non-Slip Removable Adhesive Craft Vinyl (Outdoor/Indoor Vinyl) Apply, Remove & Apply Again! No Residue when peeling! Comparable to 3M - No Transfer Tape ProvidedGreat to use on glass, metal, plastic, and much more! Please clean surface before use!Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply a transfer tape to transfer design off of the backing and place on your smooth & clean surfaceWeatherproof / 7+ years durabilityIron on Heat Transfer Vinyl - For Any Garment or Fabric Printed on Siser ColorPrint Easy (TTD High-Tack Mask Provided)Heat Transfer is printed without the carrier. Siser TTD Easy Mask is provided for applicationCut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply TTD Easy Mask to transfer design off of the backing and place on your garment face upCan be applied with a home iron and/or heat press CUTTER SETTINGSCricut: Blade: Standard Setting: Iron OnSilhouette Cameo: Blade: Standard, 3 Material: Heat Transfer, Smooth Speed: 8 Force: 6Scan N Cut: Blade: Standard, 2 Cut Speed: 1 Cut Pressure: 1Roland GS/GX-24: Blade: 45° Gram Force: 80-90 Offset: 250 Speed: 25-50 cm/sGraphtec: Blade: 45° Gram Force: 9 Tool: CB09U+0 Speed: 25 cm/sMH, SC2, LP3, & Titan 1: Blade: 45°/60° Gram Force: 80-85 Speed: 300mm/s *Blade Advancing VariesTitan 2 & 3 Blade: 45°/60° Gram Force: 60-65 Speed: 300mm/s *Blade Advancing VariesSettings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs. APPLICATION INSTRUCTIONSApplication Instructions (home iron) Set iron dial between Cotton and Linen Cover design with Kraft paper or non-stick cover sheet Place on flat, hard surface (ironing board not recommended) Press iron with medium/firm pressure (do not slide iron) Press each section of design for 15 seconds If areas of design lift after application, replace cover sheet and re-press for 10 seconds Peel carrier hot or coldApplication Instructions (heat press) Cut material - don't mirror! Weed excess material Mask with TTD High Tack Mask Preheat garment for 2-3 seconds Apply design at 305°F/150°C Use medium pressure for 10-15 seconds Peel carrier hot or cold Cover and reheat for 2-3 seconds RECOMMENDED ACCESSORIES & CAREPatterned Vinyls Apply to: 100% cotton Poly/cotton blends 100% polyester Leather Lycra®/spandexRecommended Accessories: Weeder/Tweezers Laundering: Wait 24 hours before 1st wash Machine wash cold / mild detergent Dry on normal dryer setting Do not dry clean Do not bleach SIZE AND HOW TO APPLY1) Do not mirror 2) Cut on pattern 3) Weed excess vinyl 4) Apply and peel mask 5) Press 1) Do not mirror 2) Cut on pattern 3) Weed excess vinyl 4) Apply and peel mask CUSTOM PATTERNS AND DESIGNSHave your own patterns you want to print? Contact us today!